水墨印刷機在紙箱包裝機械中常被使用，下面大家講講水墨印刷機的使用技巧，供大家參考。

通過背面曝光可設置基層，以獲得所需的浮雕，并增強聚酯支撐膜和感光性樹脂層的粘合性。正確的背部暴露從聚酯支撐膜方向暴露，可以在洗滌過程中保護好的圖案，并防止倒塌的救濟。

曝光后應立即進行曝光，主要是因?yàn)閿z影活動會逐漸消失，造成曝光時間較長，曝光量和曝光量差。

當樹脂板層保證撕裂時，感光版的感光度迅速衰減，應立即將膠片放置在板內或在10分鐘內曝光，以便   好的效果。

主曝光時間可以由主曝光試驗確定，感光性樹脂通過聚合成不溶性，一個印版就可以再現膠片上的精細圖案。要將空氣釋放到手擦真空膜和密封負面版本的主要暴露前。

板材   要干燥，否則會影響板材的厚度均勻性，干燥時，水墨印刷機不要讓印刷版面和其他表面接觸，不要用手指接觸印刷表面，否則會留下痕跡。但在去堅持之前，   要?jiǎng)h除任何斑點的表面上的板。要堅持，要清理后面的樹脂版剩下的斑點，如果你不清理這些東西，會影響板的厚度均勻性和膠帶。

Ink printing machine is often used in carton packaging machinery. Let's talk about the use skills of ink printing machine for your reference.

The base layer can be set through back exposure to obtain the required relief and enhance the adhesion of polyester support film and photosensitive resin layer. The correct back exposure from the direction of the polyester support film can protect the pattern during washing and prevent collapse relief.

Exposure should be carried out immediately after exposure, mainly because photography activities will gradually disappear, resulting in long exposure time, poor exposure and exposure.

When the resin plate ensures tearing, the sensitivity of the photosensitive plate will decay rapidly, and the film shall be placed in the plate or exposed within 10 minutes immediately for good effect.

The main exposure time can be determined by the main exposure test. The photosensitive resin can be polymerized into insoluble, and the fine pattern on the film can be reproduced in one plate. To release air to hand wipe the vacuum film and seal the negative version of the main exposure before.

The plate should be dry, otherwise it will affect the thickness uniformity of the plate. When drying, the ink printer should not let the printing plate contact with other surfaces, and should not touch the printing surface with fingers, otherwise it will leave traces. But before going to stick, remove any spots on the surface of the board. Insist on cleaning the remaining spots of the resin plate at the back. If you don't clean these things, it will affect the thickness uniformity of the board and the tape.